close

Se connecter

Se connecter avec OpenID

Closet Culture Install Sheets

IntégréTéléchargement
Closet Culture Install Sheets
Closet Kits 2', 4', 6' and 8'
8' Closet Display
Shoe Rack Kit
Pant Rack Kit
Basket Surround Kit
(ENG/FR)
(ENG/FR)
(ENG/FR)
(ENG/FR)
(ENG/FR)
Installation Instructions
Closet Kits 2', 4', 6' and 8'
0300-KITA-2CN, 0300-KITA-4CN, 0300-KITA-6CN and 0300-KITA-8CN
Tools Needed:
STEP 1: Measure 86" from the floor and make two marks on the wall with a pencil (Figure 1).
• Tape measure
• Stud finder
• Level
• Pencil
• Power drill / Phillips-head
screw driver
STEP 2: Use a stud finder to find and mark the location of wall studs on the wall.
Includes:
• 16" Shelf Bracket
STEP 3: Install the hang rail into wall studs (the top of the hang rail at 86") using the provided screws
and a level (Figure 1).
a. Installing into wall studs is highly recommended as the hang rail supports the weight
of the entire installed system.
b. If wall studs can’t be located use heavy duty drywall anchors to support the hang rail.
STEP 4: Starting from one side of the closet, hang a wall standard on the hang rail and use a hang rail
cover to create the proper space between that and the next wall standard. Follow this method
until all the wall standards are hanging from the hang rail (Figure 2).
STEP 5: Install shelf brackets by removing the top plastic caps (it’s easiest from the front) and inserting
into the wall standards in the desired configuration (Figure 3).
• 48" Hang Rail
STEP 6: Install wood or wire shelves (sold separately) by inserting the assembled shelves (which have
four shelf clips) into the slots on the shelf brackets (Figure 4).
STEP 7: When fully seated, push the shelf towards the wall to secure the clips to the bracket (Figure 5).
Install the plastic bracket cap on top to lock in place.
STEP 8: Install closet hooks by inserting into the bottom of the shelf brackets and snapping into place
(Figure 6).
• 22" Hang Rail Cover
• Closet Pole Kit
• 48" Wall Standard
STEP 9: Assemble closet poles and snap into the closet hooks.
a. If using the poles in separate 2' sections, insert the plastic connector and end cap onto
each end of the closet pole (Figure 7a & 7c).
b. If connecting multiple poles together, insert the connectors and push the poles together,
then put an end cap on the ends of the assembly (Figure 7b & 7c).
c. C
ommon closet pole heights (measuring from the floor to the top of the closet pole):
66" for a single pole configuration; 40" and 80" for a double pole configuration (Figure 1).
STEP 10: W
hen system is assembled and in place (Figure 3), level the wall standards vertically and
secure to the wall with two screws per standard (one at the top, one at the bottom).
a. It is likely that the wall standards will not be located over wall studs. Since the weight of
the system is supported by the hang rail (which is mounted into wall studs), the screws
in the wall standards are meant to provide side-to-side stability for the system and not a
load-bearing function.
b. If desired, the mounting screws can also be installed into drywall anchors (not provided).
• Closet Pole Hook
22.4"
66"
66
40"
40
80"
80
86"
86
• Mounting Screws
Figure 1
Figure 2
Installation Instructions
Instructions
Closet Kits 2', 4', 6' and 8'
0300-KITA-2CN, 0300-KITA-4CN, 0300-KITA-6CN and 0300-KITA-8CN
0300-KITA-8CN,
Figure 3
2'
4'
6'
8'
Figure 4
Figure 5
Figure 6
ECN
REV
DATE
TOLERANCE UNLESS OTHERWISE SPECIFIED
3 PL DEC .005
2 PL DEC .010
ANGLES 1/2
MATERIAL:
FINISH:
N/A
Figure 7a
2700 Oak Industrial Dr. NE
Grand Rapids, MI 49505
800-253-1561
www.kv.com
customer.service@kv.com
Figure 7b
DESCRIPTION
DWN BY:
DATE:
5/20/2016
APPR
SCALE:
1:4
DESCRIPTION:
PART NO:
WOODSHELF-ASM
CHK'D BY:
-
SHEET SIZE:
D
SHEET 1 OF 1
Figure 7c
©2016 Knape & Vogt. KV and the KV logo are trademarks of Knape & Vogt.
310535/0616
Instructions d'installation
Ensembles de garde-robe 61 cm, 122 cm, 183 cm et 244 cm
0300-KITA-2CN, 0300-KITA-4CN, 0300-KITA-6CN et 0300-KITA-8CN
Outils Requis:
étape 1: Mesurez 218 cm à partir du plancher et marquez deux repères sur le mur avec le crayon
(Figure 1).
• Ruban à mesurer
• Détecteur de montants
• Niveau
• Crayon
• Perceuse électrique/
tournevis Phillips
a. Le rail d’accrochage supporte entièrement le poids de l’ensemble un fois assemblé,
une fixation sur les montants du mur est très recommandée.
Contient:
b. S
I vous ne pouvez pas localiser les montants, utilisez des ancrages ultra-robustes
appropriés au revêtement de vos murs.
• Support à tablette 40,6cm
• Rail d’accrochage
121,9cm
étape 2: Trouvez les montants à l’aide du détecteur et marquez leurs localisations.
étape 3: Installez le rail d’accrochage sur les montants du mur (le dessus du rail à 218 cm) à l’aide
du niveau et des vis incluses (Figure 1).
étape 4: En débutant par un côté de la garde-robe, accrochez un montant sur le rail d’accrochage
et utilisez le cache-rail pour espacer correctement les montants. Procédez ainsi jusqu’au
positionnement de tous les montants sur le rail (Figure 2).
étape 5: Installez les supports à tablette en retirant les capuchons de plastique (c’est plus facile par
le devant) et en les installant sur les montants dans la configuration désirée (Figure 7).
étape 6: Installez les tablettes laminées ou grillagées (vendues séparément) en insérant les tablettes
assemblées (qui comportent 4 attaches) sur les encoches des supports à tablettes (Figure 3).
étape 7: Lorsque les tablettes sont bien positionnées, poussez-les vers le mur afin de fixer les attaches
au support. Installez les capuchons de plastique sur les dessus pour les verrouiller en position
(Figure 4).
• Cache-rail 121,9cm
étape 8: Installez les crochets en les insérant sur le dessous des supports à tablette et en les enclenchant
en position (Figure 5).
étape 9: Assemblez les tringles de garde-robe et enclenchez-les sur les crochets.
• Ensemble pour tringle
de garde-robe
a. Si vous utilisez les tringles en sections de 122 cm séparées, insérez les connecteurs de
plastique et les embouts à chaque extrémité des tringles (Figure 6b & 6c).
b. Si vous relies plusieurs tringles une à l’autre, insérez les connecteurs et reliez les tringles
ensemble, insérez ensuite les embouts à chaque extrémité (Figure 6b & 6c).
c. La hauteur standard pour les tringles (en mesurant du plancher jusqu’au dessus de la
tringle) est de 168 cm pour un agencement à tringle simple, 102 cm et 203 cm pour
un agencement à 2 tringles (Figure 1).
étape 10: Lorsque l’ensemble est positionné, nivelez les montants à la verticale et fixez-les au mur
avec 2 vis (une vis au haut et une au bas).
• Montant 121,9cm
a. Il est probable que les montants ne seront pas alignés sur les montants du mur. Puisque le
poids de l’ensemble est supporté par le rail d’accrochage (qui lui est fixé aux montants du
mur), les vis des montants visent à stabiliser l’ensemble et non à le supporter.
b. S
I désiré, les vis d’installation peuvent être installées dans des ancrages pour panneaux
de gypse (non-inclus).
• Crochet pour tringle
56,9 cm
168 cm
66
102 cm
40
203 cm
80
218 cm
86
• Vis d’installation
Figure 1
Figure 2
Instructions d’installation
Ensembles de garde-robe 61 cm, 122 cm, 183 cm et 244 cm
0300-KITA-2CN, 0300-KITA-4CN, 0300-KITA-6CN et 0300-KITA-8CN
Figure 3
61 cm
122 cm
183 cm
244 cm
Figure 4
Figure 5
Figure 6
ECN
REV
DATE
TOLERANCE UNLESS OTHERWISE SPECIFIED
3 PL DEC .005
2 PL DEC .010
ANGLES 1/2
MATERIAL:
FINISH:
N/A
Figure 7a
2700 Oak Industrial Dr. NE
Grand Rapids, MI 49505
800-253-1561
www.kv.com
customer.service@kv.com
Figure 7b
DESCRIPTION
DWN BY:
DATE:
5/20/2016
APPR
SCALE:
1:4
DESCRIPTION:
PART NO:
WOODSHELF-ASM
CHK'D BY:
-
SHEET SIZE:
D
SHEET 1 OF 1
Figure 7c
©2016 Knape & Vogt. KV and the KV logo are trademarks of Knape & Vogt.
310535/0616
Installation Instructions
8' Closet Display
0300-8 DSPL
STEP 1: Install the hang rail (the top of the hang rail at 86") using the provided
screws and a level.
Tools Needed:
• Tape measure
• Level
• Power drill / Phillips-head screw driver
Includes:
• (6) 16" Shelf Bracket
STEP 2: Starting from one side of the bay, hang a wall standard on the hang
rail and use a hang rail cover to create the proper space between
that and the next wall standard. Follow this method until all the wall
standards are hanging from the hang rail (Figure 2).
STEP 3: Install shelf brackets by removing the top plastic caps (it’s
easiest from the front) and inserting into the wall standards in the
configuration as shown in Figure 1.
• ( 2) Basket Surround Kits
& Baskets
U.S.
• (2) 48" Hang Rail
• (4) 22" Hang Rail Cover
• (2) Shoe Rack Kits
U.S.
PURCHASE
METRIC DIMENSIONS SHOWN AS [ ] ARE
PROVIDED AS REFERENCE ONLY. ALL
TOLERANCES TO BE HELD TO ENGLISH
DIMENSIONS
30577
A
1/14/2016
ECN
REV
DATE
图纸标注的公制尺寸仅供参考,所有尺寸以英制为准.
MATERIAL:
TOLERANCE
UNLESS OTHERWISE
SPECIFIED
材料
N/A
除图纸特别给定的公差
外,其他按自然公差处理
表面处理
®
N/A
KNAPE & VOGT
DO NOT SCALE DRAWING
®
不要对图纸进行实际测量而获得尺寸值
R. SYTSMA
APPR
SURROUND ASSEMBLY
0335-SRND
PART NO:
C
RSS
1:3
1/14/2016
DESCRIPTION:
MANUFACTURING PROCESS
CRITICAL DIMENSION
产品加工过程特性尺寸
• (4) Closet Pole Kit
DATE:
DWN BY:
PRODUCT ENGINEERING
CRITICAL DIMENSION
产品设计特性尺寸
XX
XX
KM/RSS
DESCRIPTION
THIS DRAWING IS THE SOLE PROPERTY OF KNAPE & VOGT
MANUFACTURING COMPANY (KV) AND EMBODIES CONFIDENTIAL
PROPRIETY INFORMATION. ALL RIGHTS IN THIS DOCUMENT AND THE
INFORMATION CONTAINED THEREIN ARE RESERVED. THIS DOCUMENT IS
PROVIDED IN CONFIDENCE FOR A SPECIFIC PURPOSE AND MAY NOT
BE USED, COPIED, OR DISCLOSED TO OTHERS FOR ANY OTHER PURPOSE
WITHOUT EXPRESS WRITTEN CONSENT OF KV. BY ACCEPTING THIS
DOCUMENT, THE RECIPIENT AGREES TO ABIDE BY THE FOREGOING
RESTRICTIONS AND TO RETURN THE DOCUMENT ON REQUEST WHEN THE
PERMITTED USE IS COMPLETE.
© 2012 KNAPE & VOGT MANUFACTURING COMPANY. ALL RIGHTS
RESERVED.
SHEET SIZE:
SCALE:
CHK'D BY:
™
FINISH:
3 PL DEC .005
2 PL DEC .015
FRACTIONS 1/64
ANGLES 1
RELEASE DRAWING
SHEET 1 OF 1
Figure 1
• (2) 48" Wall Standard
(3) 78" Wall Standard
U.S.
• (1) Pants Rack Kits
PURCHASE
METRIC DIMENSIONS SHOWN AS [ ] ARE
PROVIDED AS REFERENCE ONLY. ALL
TOLERANCES TO BE HELD TO ENGLISH
DIMENSIONS
图纸标注的公制尺寸仅供参考,所有尺寸以英制为准.
材料
4/12/2016
PICTORAL REVISION
RSS
1/6/2016
RELEASE DRAWING
KM/RSS
ECN
REV
DATE
DESCRIPTION
APPR
N/A
™
FINISH:
3 PL DEC .005
2 PL DEC .015
FRACTIONS 1/64
ANGLES 1
表面处理
®
N/A
KNAPE & VOGT
DO NOT SCALE DRAWING
®
不要对图纸进行实际测量而获得尺寸值
DWN BY:
PRODUCT ENGINEERING
CRITICAL DIMENSION
产品设计特性尺寸
LJV
DESCRIPTION:
MANUFACTURING PROCESS
CRITICAL DIMENSION
产品加工过程特性尺寸
XX
B
A
MATERIAL:
TOLERANCE
UNLESS OTHERWISE
SPECIFIED
除图纸特别给定的公差
外,其他按自然公差处理
XX
30891
30577
DATE:
THIS DRAWING IS THE SOLE PROPERTY OF KNAPE & VOGT MANUFACTURING
COMPANY (KV) AND EMBODIES CONFIDENTIAL PROPRIETY INFORMATION.
ALL RIGHTS IN THIS DOCUMENT AND THE INFORMATION CONTAINED THEREIN
ARE RESERVED. THIS DOCUMENT IS PROVIDED IN CONFIDENCE FOR A
SPECIFIC PURPOSE AND MAY NOT BE USED, COPIED, OR DISCLOSED TO
OTHERS FOR ANY OTHER PURPOSE WITHOUT EXPRESS WRITTEN CONSENT OF
KV. BY ACCEPTING THIS DOCUMENT, THE RECIPIENT AGREES TO ABIDE BY
THE FOREGOING RESTRICTIONS AND TO RETURN THE DOCUMENT ON
REQUEST WHEN THE PERMITTED USE IS COMPLETE.
© 2012 KNAPE & VOGT MANUFACTURING COMPANY. ALL RIGHTS
RESERVED.
7/15/2015
SCALE:
CHK'D BY:
1:4
SHEET SIZE:
C
RSS
SHOE RACK ASSEMBLY
PART NO:
SHEET 1 OF 1
0335-SRK
• (6) Closet Pole Hook
22.4"
• (1) Mounting Screws
(1) Shelf Screws/Clips
PURCHASE
METRIC DIMENSIONS SHOWN AS [ ] ARE
PROVIDED AS REFERENCE ONLY. ALL
TOLERANCES TO BE HELD TO ENGLISH
DIMENSIONS
图纸标注的公制尺寸仅供参考,所有尺寸以英制为准.
材料
除图纸特别给定的公差
外,其他按自然公差处理
4/11/2016
A
1/6/2016
ECN
REV
DATE
™
FINISH:
3 PL DEC .005
2 PL DEC .015
FRACTIONS 1/64
ANGLES 1
表面处理
®
N/A
DO NOT SCALE DRAWING
XX
30891
N/A
不要对图纸进行实际测量而获得尺寸值
XX
B
30577
MATERIAL:
TOLERANCE
UNLESS OTHERWISE
SPECIFIED
PRODUCT ENGINEERING
CRITICAL DIMENSION
产品设计特性尺寸
MANUFACTURING PROCESS
CRITICAL DIMENSION
产品加工过程特性尺寸
KNAPE & VOGT
®
DWN BY:
R. SYTSMA
DESCRIPTION:
PART NO:
DATE:
ASSEMBLY UPDATE
RSS
RELEASE DRAWING
KM/RSS
DESCRIPTION
APPR
THIS DRAWING IS THE SOLE PROPERTY OF KNAPE & VOGT MANUFACTURING
COMPANY (KV) AND EMBODIES CONFIDENTIAL PROPRIETY INFORMATION.
ALL RIGHTS IN THIS DOCUMENT AND THE INFORMATION CONTAINED THEREIN
ARE RESERVED. THIS DOCUMENT IS PROVIDED IN CONFIDENCE FOR A
SPECIFIC PURPOSE AND MAY NOT BE USED, COPIED, OR DISCLOSED TO
OTHERS FOR ANY OTHER PURPOSE WITHOUT EXPRESS WRITTEN CONSENT OF
KV. BY ACCEPTING THIS DOCUMENT, THE RECIPIENT AGREES TO ABIDE BY
THE FOREGOING RESTRICTIONS AND TO RETURN THE DOCUMENT ON
REQUEST WHEN THE PERMITTED USE IS COMPLETE.
© 2012 KNAPE & VOGT MANUFACTURING COMPANY. ALL RIGHTS
RESERVED.
2/10/2016
SCALE:
1:4
CHK'D BY:
PANTS RACK ASSEMBLY
0335-PRK
RSS
SHEET SIZE:
C
SHEET 1 OF 1
Figure 2
Installation Instructions
Instructions
8’
Closet
Display
Closet
Kits
2', 4', 6' and 8'
0300-8
DSPL
0300-KITA-2CN,
0300-KITA-4CN, 0300-KITA-6CN and 0300-KITA-8CN,
STEP 4: Install wood shelves by inserting the wood shelf clips into the four pre-drilled holes and inserting the assembled shelves into the slots on the shelf brackets (Figure 3).
STEP 5: W
hen fully seated, push the shelf towards the wall to secure the clips to the bracket (Figure 4).
Install the plastic bracket cap on top to lock in place.
STEP 6: Install the surround assemblies by inserting the six tabs into the slots on the shelf brackets.
When fully seated, push the assembly towards the wall to secure the tabs to the bracket (Figure 5).
Install the plastic bracket cap on the top to lock in place.
Figure 3
Figure 5
Figure 4
ECN
REV
DATE
TOLERANCE UNLESS OTHERWISE SPECIFIED
3 PL DEC .005
2 PL DEC .010
ANGLES 1/2
MATERIAL:
FINISH:
N/A
DESCRIPTION
DWN BY:
DATE:
5/20/2016
APPR
SCALE:
1:4
DESCRIPTION:
PART NO:
CHK'D BY:
-
WOODSHELF-ASM
SHEET SIZE:
D
SHEET 1 OF 1
STEP 7: P
lace the wire mesh baskets into their surround assemblies (Figure 6).
STEP 8: Place the shoe rack into its surround assembly (Figure 7).
STEP 9: Slide the pants rack into its surround assemble (Figure 8).
ECN
TOLERANCE UNL
3 PL DEC .005
2
MATERIAL:
Figure 6
Figure 7
Figure 8
ECN
REV
DATE
TOLERANCE UNLESS OTHERWISE SPECIFIED
3 PL DEC .005
2 PL DEC .010
ANGLES 1/2
MATERIAL:
FINISH:
N/A
DESCRIPTION
DWN BY:
DATE:
5/20/2016
APPR
SCALE:
1:8
DESCRIPTION:
PART NO:
CHK'D BY:
-
0300-KITA
SHEET SIZE:
D
SHEET 1 OF 1
STEP 10: Install closet hooks by inserting into the bottom of the shelf brackets and snapping into place
(Figure 9).
STEP 11: Assemble closet poles and snap into the closet hooks.
a. For the 2' pole section (40" from floor), insert the plastic
connector and end cap onto each end of the closet pole (Figure 10a & 10c).
b. F
or the 6' pole section (80" from floor), insert the plastic
connector and end cap onto each end of the closet pole (Figure 10b & 10c).
STEP 12: W
hen system is assembled and in place (Figure 1), level the wall standards vertically and
secure to the wall with two screws per standard (one at the top, one at the bottom).
Figure 9
2700 Oak Industrial Dr. NE
Grand Rapids, MI 49505
800-253-1561
www.kv.com
customer.service@kv.com
Figure 10a
Figure 10b
Figure 10c
©2016 Knape & Vogt. KV and the KV logo are trademarks of Knape & Vogt.
310535/0616
Installation Instructions / Instructions d’installation
Shoe Rack Kit / Ensemble pour support à souliers
0335-SRK-CN
Tools Needed:
STEP 1: Remove the top plastic caps (it’s easier from the front) from the shelf brackets).
• Phillips-head screw driver
STEP 2: Insert the shelf brackets into the wall standards in the desired location (Figure 1).
Includes:
STEP 3: If installing wood fascia, attach to the surround by fastening the included mounting screws
into pilot holes on the fascia. Do not overtighten.
U.S.
STEP 4: Install the surround assembly by inserting the six shelf tabs into the slots on the shelf brackets
(Figure 2).
STEP 5: When fully seated, push the assembly towards the wall to secure the tabs to the bracket (Figure 3).
Install the plastic bracket cap on top to lock in place.
STEP 6: P
lace shoe rack into the surround assembly (Figure 4).
NOTE: Shoe rack is reversible.
PURCHASE
Outils Requis:
METRIC DIMENSIONS SHOWN AS [ ] ARE
PROVIDED AS REFERENCE ONLY. ALL
TOLERANCES TO BE HELD TO ENGLISH
DIMENSIONS
图纸标注的公制尺寸仅供参考,所有尺寸以英制为准.
材料
•T
ournevis Phillips
除图纸特别给定的公差
外,其他按自然公差处理
3 PL DEC .005
2 PL DEC .015
FRACTIONS 1/64
ANGLES 1
Contient:
4/12/2016
A
1/6/2016
ECN
REV
DATE
N/A
™
表面处理
®
N/A
KNAPE & VOGT
®
PRODUCT ENGINEERING
CRITICAL DIMENSION
产品设计特性尺寸
XX
30891
FINISH:
DO NOT SCALE DRAWING
不要对图纸进行实际测量而获得尺寸值
XX
B
30577
MATERIAL:
TOLERANCE
UNLESS OTHERWISE
SPECIFIED
MANUFACTURING PROCESS
CRITICAL DIMENSION
产品加工过程特性尺寸
DWN BY:
DATE:
LJV
DESCRIPTION:
étape 1: Retirez les capuchons de plastique (c’est plus facile par le devant) des supports à tablette.
PICTORAL REVISION
RSS
RELEASE DRAWING
KM/RSS
DESCRIPTION
APPR
THIS DRAWING IS THE SOLE PROPERTY OF KNAPE & VOGT MANUFACTURING
COMPANY (KV) AND EMBODIES CONFIDENTIAL PROPRIETY INFORMATION.
ALL RIGHTS IN THIS DOCUMENT AND THE INFORMATION CONTAINED THEREIN
ARE RESERVED. THIS DOCUMENT IS PROVIDED IN CONFIDENCE FOR A
SPECIFIC PURPOSE AND MAY NOT BE USED, COPIED, OR DISCLOSED TO
OTHERS FOR ANY OTHER PURPOSE WITHOUT EXPRESS WRITTEN CONSENT OF
KV. BY ACCEPTING THIS DOCUMENT, THE RECIPIENT AGREES TO ABIDE BY
THE FOREGOING RESTRICTIONS AND TO RETURN THE DOCUMENT ON
REQUEST WHEN THE PERMITTED USE IS COMPLETE.
© 2012 KNAPE & VOGT MANUFACTURING COMPANY. ALL RIGHTS
RESERVED.
étape 2: Insérez les supports à tablette sur les montants en position souhaitée (Figure 1).
7/15/2015
SCALE:
1:4
CHK'D BY:
0335-SRK
SHEET SIZE:
étape 3: Si vous installez la bordure de bois, fixez-la au cadre en vissant les vis d’installation incluses
dans les trous guides de la bordure. Ne pas trop serrer.
RSS
SHOE RACK ASSEMBLY
PART NO:
C
SHEET 1 OF 1
U.S.
étape 4: Installez le cadre en introduisant les six taquets de la tablette dans les insertions sur les supports
à tablette (Figure 2).
étape 5: Lorsque bien positionné, poussez l’ensemble vers le mur afin de fixer les attaches au support
(Figure 3). Installez les capuchons de plastique sur les dessus pour les verrouiller en position.
étape 6: Positionnez le support à souliers sur le cadre (Figure 4).
NOTEZ: Que le support à souliers est réversible
PURCHASE
METRIC DIMENSIONS SHOWN AS [ ] ARE
PROVIDED AS REFERENCE ONLY. ALL
TOLERANCES TO BE HELD TO ENGLISH
DIMENSIONS
图纸标注的公制尺寸仅供参考,所有尺寸以英制为准.
材料
除图纸特别给定的公差
外,其他按自然公差处理
4/12/2016
A
1/6/2016
ECN
REV
DATE
™
FINISH:
3 PL DEC .005
2 PL DEC .015
FRACTIONS 1/64
ANGLES 1
表面处理
®
N/A
DO NOT SCALE DRAWING
XX
30891
N/A
不要对图纸进行实际测量而获得尺寸值
XX
B
30577
MATERIAL:
TOLERANCE
UNLESS OTHERWISE
SPECIFIED
PRODUCT ENGINEERING
CRITICAL DIMENSION
产品设计特性尺寸
MANUFACTURING PROCESS
CRITICAL DIMENSION
产品加工过程特性尺寸
KNAPE & VOGT
®
DWN BY:
LJV
DESCRIPTION:
PART NO:
DATE:
PICTORAL REVISION
RSS
RELEASE DRAWING
KM/RSS
DESCRIPTION
APPR
THIS DRAWING IS THE SOLE PROPERTY OF KNAPE & VOGT MANUFACTURING
COMPANY (KV) AND EMBODIES CONFIDENTIAL PROPRIETY INFORMATION.
ALL RIGHTS IN THIS DOCUMENT AND THE INFORMATION CONTAINED THEREIN
ARE RESERVED. THIS DOCUMENT IS PROVIDED IN CONFIDENCE FOR A
SPECIFIC PURPOSE AND MAY NOT BE USED, COPIED, OR DISCLOSED TO
OTHERS FOR ANY OTHER PURPOSE WITHOUT EXPRESS WRITTEN CONSENT OF
KV. BY ACCEPTING THIS DOCUMENT, THE RECIPIENT AGREES TO ABIDE BY
THE FOREGOING RESTRICTIONS AND TO RETURN THE DOCUMENT ON
REQUEST WHEN THE PERMITTED USE IS COMPLETE.
© 2012 KNAPE & VOGT MANUFACTURING COMPANY. ALL RIGHTS
RESERVED.
7/15/2015
SCALE:
1:4
CHK'D BY:
SHOE RACK ASSEMBLY
0335-SRK
RSS
SHEET SIZE:
C
SHEET 1 OF 1
Figure 1
Figure 2
ECN
REV
DATE
TOLERANCE UNLESS OTHERWISE SPECIFIED
3 PL DEC .005
2 PL DEC .010
ANGLES 1/2
MATERIAL:
FINISH:
N/A
2700 Oak Industrial Dr. NE
Grand Rapids, MI 49505
800-253-1561
www.kv.com
customer.service@kv.com
Figure 3
DWN
DESC
PART
Figure 4
ECN
REV
DATE
TOLERANCE UNLESS OTHERWISE SPECIFIED
3 PL DEC .005
2 PL DEC .010
ANGLES 1/2
MATERIAL:
FINISH:
©2016 Knape & Vogt. KV and the KV logo are trademarks of Knape & Vogt.
N/A
DESCRIPTION
DWN BY:
DATE:
5/20/2016
APPR
SCALE:
1:8
CHK'D BY:
DESCRIPTION:
PART NO:
0300-KITA
310532/0616
-
SHEET SIZE:
D
SHEET 1 OF 1
Installation Instructions / Instructions d’installation
Pants Rack Kit / Ensemble pour support à pantalons
0335-PRK-CN
Tools Needed:
STEP 1: Remove the top plastic caps (it’s easier from the front) from the shelf brackets.
• None
STEP 2: Insert the shelf brackets into the wall standards in the desired location (Figure 1).
Includes:
STEP 3: Install the surround assembly by inserting the six shelf tabs into the slots on the shelf brackets
(Figure 2).
U.S.
STEP 4: When fully seated, push the assembly towards the wall to secure the tabs to the bracket (Figure 3).
Install the plastic bracket cap on top to lock in place (Figure 4).
PURCHASE
METRIC DIMENSIONS SHOWN AS [ ] ARE
PROVIDED AS REFERENCE ONLY. ALL
TOLERANCES TO BE HELD TO ENGLISH
DIMENSIONS
图纸标注的公制尺寸仅供参考,所有尺寸以英制为准.
Outils Requis:
• Aucun
材料
30891
4/11/2016
A
1/6/2016
ECN
REV
DATE
除图纸特别给定的公差
外,其他按自然公差处理
N/A
™
FINISH:
3 PL DEC .005
2 PL DEC .015
FRACTIONS 1/64
ANGLES 1
表面处理
®
N/A
KNAPE & VOGT
DO NOT SCALE DRAWING
®
不要对图纸进行实际测量而获得尺寸值
PRODUCT ENGINEERING
CRITICAL DIMENSION
产品设计特性尺寸
XX
XX
B
30577
MATERIAL:
TOLERANCE
UNLESS OTHERWISE
SPECIFIED
MANUFACTURING PROCESS
CRITICAL DIMENSION
产品加工过程特性尺寸
DATE:
DWN BY:
R. SYTSMA
DESCRIPTION:
ASSEMBLY UPDATE
RSS
RELEASE DRAWING
KM/RSS
DESCRIPTION
APPR
étape 1: Retirez les capuchons de plastique (c’est plus facile par le devant) des supports à tablette.
THIS DRAWING IS THE SOLE PROPERTY OF KNAPE & VOGT MANUFACTURING
COMPANY (KV) AND EMBODIES CONFIDENTIAL PROPRIETY INFORMATION.
ALL RIGHTS IN THIS DOCUMENT AND THE INFORMATION CONTAINED THEREIN
ARE RESERVED. THIS DOCUMENT IS PROVIDED IN CONFIDENCE FOR A
SPECIFIC PURPOSE AND MAY NOT BE USED, COPIED, OR DISCLOSED TO
OTHERS FOR ANY OTHER PURPOSE WITHOUT EXPRESS WRITTEN CONSENT OF
KV. BY ACCEPTING THIS DOCUMENT, THE RECIPIENT AGREES TO ABIDE BY
THE FOREGOING RESTRICTIONS AND TO RETURN THE DOCUMENT ON
REQUEST WHEN THE PERMITTED USE IS COMPLETE.
© 2012 KNAPE & VOGT MANUFACTURING COMPANY. ALL RIGHTS
RESERVED.
2/10/2016
SCALE:
étape 2: Insérez les supports à tablette sur les montants en position souhaitée (Figure 1).
CHK'D BY:
1:4
RSS
PANTS RACK ASSEMBLY
PART NO:
SHEET SIZE:
C
SHEET 1 OF 1
0335-PRK
étape 3: Installez le cadre en introduisant les six taquets de la tablette dans les insertions sur les supports à
tablette (Figure 2).
Contient:
U.S.
étape 4: Lorsque bien positionné, poussez l’ensemble vers le mur afin de fixer les attaches au support
(Figure 3). Installez les capuchons de plastique sur les dessus pour les verrouiller en position
(Figure 4).
PURCHASE
METRIC DIMENSIONS SHOWN AS [ ] ARE
PROVIDED AS REFERENCE ONLY. ALL
TOLERANCES TO BE HELD TO ENGLISH
DIMENSIONS
图纸标注的公制尺寸仅供参考,所有尺寸以英制为准.
材料
除图纸特别给定的公差
外,其他按自然公差处理
XX
30891
4/11/2016
A
1/6/2016
ECN
REV
DATE
N/A
™
FINISH:
3 PL DEC .005
2 PL DEC .015
FRACTIONS 1/64
ANGLES 1
表面处理
®
N/A
DO NOT SCALE DRAWING
不要对图纸进行实际测量而获得尺寸值
XX
B
30577
MATERIAL:
TOLERANCE
UNLESS OTHERWISE
SPECIFIED
PRODUCT ENGINEERING
CRITICAL DIMENSION
产品设计特性尺寸
MANUFACTURING PROCESS
CRITICAL DIMENSION
产品加工过程特性尺寸
KNAPE & VOGT
®
DWN BY:
R. SYTSMA
DESCRIPTION:
PART NO:
DATE:
ASSEMBLY UPDATE
RSS
RELEASE DRAWING
KM/RSS
DESCRIPTION
APPR
THIS DRAWING IS THE SOLE PROPERTY OF KNAPE & VOGT MANUFACTURING
COMPANY (KV) AND EMBODIES CONFIDENTIAL PROPRIETY INFORMATION.
ALL RIGHTS IN THIS DOCUMENT AND THE INFORMATION CONTAINED THEREIN
ARE RESERVED. THIS DOCUMENT IS PROVIDED IN CONFIDENCE FOR A
SPECIFIC PURPOSE AND MAY NOT BE USED, COPIED, OR DISCLOSED TO
OTHERS FOR ANY OTHER PURPOSE WITHOUT EXPRESS WRITTEN CONSENT OF
KV. BY ACCEPTING THIS DOCUMENT, THE RECIPIENT AGREES TO ABIDE BY
THE FOREGOING RESTRICTIONS AND TO RETURN THE DOCUMENT ON
REQUEST WHEN THE PERMITTED USE IS COMPLETE.
© 2012 KNAPE & VOGT MANUFACTURING COMPANY. ALL RIGHTS
RESERVED.
2/10/2016
SCALE:
1:4
CHK'D BY:
PANTS RACK ASSEMBLY
0335-PRK
RSS
SHEET SIZE:
C
SHEET 1 OF 1
Figure 1
2700 Oak Industrial Dr. NE
Grand Rapids, MI 49505
800-253-1561
www.kv.com
customer.service@kv.com
Figure 2
Figure 3
ECN
REV
DATE
TOLERANCE UNLESS OTHERWISE SPECIFIED
3 PL DEC .005
2 PL DEC .010
ANGLES 1/2
MATERIAL:
FINISH:
N/A
DESCRIPTION
DWN BY:
DATE:
5/31/2016
APPR
SCALE:
1:4
DESCRIPTION:
PART NO:
0335-PRK
CHK'D BY:
-
SHEET SIZE:
D
SHEET 1 OF 1
Figure 4
ECN
REV
DATE
TOLERANCE UNLESS OTHERWISE SPECIFIED
3 PL DEC .005
2 PL DEC .010
ANGLES 1/2
MATERIAL:
FINISH:
N/A
DESCRIPTION
DWN BY:
DATE:
5/31/2016
APPR
SCALE:
1:4
DESCRIPTION:
PART NO:
0335-PRK
CHK'D BY:
-
SHEET SIZE:
D
SHEET 1 OF 1
©2016 Knape & Vogt. KV and the KV logo are trademarks of Knape & Vogt.
310534/0616
Installation Instructions / Instructions d’installation
Basket Surround Kit / Cadre pour panier
0335-SRND-CN
Tools Needed:
STEP 1: Remove the top plastic caps (it’s easier from the front) from the shelf brackets.
• Phillips-head screw driver
STEP 2: Insert the shelf brackets into the wall standards in the desired location (Figure 1).
Includes:
STEP 3: If installing wood fascia, attach to the surround by fastening the included mounting screws into
pilot holes on the fascia. Do not overtighten.
U.S.
STEP 4: Install the surround assembly by inserting the six shelf tabs into the slots on the shelf brackets
(Figure 2).
STEP 5: When fully seated, push the assembly towards the wall to secure the tabs to the bracket (Figure 3).
Install the plastic bracket cap on top to lock in place.
STEP 6: P
lace wire mesh basket (sold separately) into the surround assembly (Figure 4).
PURCHASE
METRIC DIMENSIONS SHOWN AS [ ] ARE
PROVIDED AS REFERENCE ONLY. ALL
TOLERANCES TO BE HELD TO ENGLISH
DIMENSIONS
图纸标注的公制尺寸仅供参考,所有尺寸以英制为准.
材料
1/14/2016
REV
DATE
®
N/A
KNAPE & VOGT
DO NOT SCALE DRAWING
®
PRODUCT ENGINEERING
CRITICAL DIMENSION
产品设计特性尺寸
XX
MANUFACTURING PROCESS
CRITICAL DIMENSION
产品加工过程特性尺寸
DATE:
DWN BY:
R. SYTSMA
1/14/2016
DESCRIPTION:
RELEASE DRAWING
KM/RSS
DESCRIPTION
APPR
THIS DRAWING IS THE SOLE PROPERTY OF KNAPE & VOGT
MANUFACTURING COMPANY (KV) AND EMBODIES CONFIDENTIAL
PROPRIETY INFORMATION. ALL RIGHTS IN THIS DOCUMENT AND THE
INFORMATION CONTAINED THEREIN ARE RESERVED. THIS DOCUMENT IS
PROVIDED IN CONFIDENCE FOR A SPECIFIC PURPOSE AND MAY NOT
BE USED, COPIED, OR DISCLOSED TO OTHERS FOR ANY OTHER PURPOSE
WITHOUT EXPRESS WRITTEN CONSENT OF KV. BY ACCEPTING THIS
DOCUMENT, THE RECIPIENT AGREES TO ABIDE BY THE FOREGOING
RESTRICTIONS AND TO RETURN THE DOCUMENT ON REQUEST WHEN THE
PERMITTED USE IS COMPLETE.
© 2012 KNAPE & VOGT MANUFACTURING COMPANY. ALL RIGHTS
RESERVED.
SHEET SIZE:
SCALE:
CHK'D BY:
™
表面处理
不要对图纸进行实际测量而获得尺寸值
XX
A
ECN
N/A
FINISH:
3 PL DEC .005
2 PL DEC .015
FRACTIONS 1/64
ANGLES 1
Outils Requis:
30577
MATERIAL:
TOLERANCE
UNLESS OTHERWISE
SPECIFIED
除图纸特别给定的公差
外,其他按自然公差处理
étape 1: Retirez les capuchons de plastique (c’est plus facile par le devant) des supports à tablette.
1:3
RSS
SURROUND ASSEMBLY
0335-SRND
PART NO:
C
SHEET 1 OF 1
• Tournevis Phillips
étape 2: Insérez les supports à tablette sur les montants en position souhaitée (Figure 1).
Contient:
étape 3: Si vous installez la bordure de bois, fixez-la au cadre en vissant les vis d’installation incluses
dans les trous guides de la bordure. Ne pas trop serrer.
U.S.
étape 4: Installez le cadre en introduisant les six taquets de la tablette dans les insertions sur les supports
à tablette (Figure 2).
étape 5: L
orsque bien positionné, poussez l’ensemble vers le mur afin de fixer les attaches au support
(Figure 3). Installez les capuchons de plastique sur les dessus pour les verrouiller en position.
étape 6: Positionnez le panier grillagé (vendu séparément) sur le cadre (Figure 4).
PURCHASE
METRIC DIMENSIONS SHOWN AS [ ] ARE
PROVIDED AS REFERENCE ONLY. ALL
TOLERANCES TO BE HELD TO ENGLISH
DIMENSIONS
图纸标注的公制尺寸仅供参考,所有尺寸以英制为准.
材料
1/14/2016
REV
DATE
™
表面处理
®
N/A
DO NOT SCALE DRAWING
不要对图纸进行实际测量而获得尺寸值
XX
A
ECN
N/A
FINISH:
3 PL DEC .005
2 PL DEC .015
FRACTIONS 1/64
ANGLES 1
XX
30577
MATERIAL:
TOLERANCE
UNLESS OTHERWISE
SPECIFIED
除图纸特别给定的公差
外,其他按自然公差处理
PRODUCT ENGINEERING
CRITICAL DIMENSION
产品设计特性尺寸
MANUFACTURING PROCESS
CRITICAL DIMENSION
产品加工过程特性尺寸
KNAPE & VOGT
®
DWN BY:
R. SYTSMA
DESCRIPTION:
PART NO:
DATE:
RELEASE DRAWING
KM/RSS
DESCRIPTION
APPR
THIS DRAWING IS THE SOLE PROPERTY OF KNAPE & VOGT
MANUFACTURING COMPANY (KV) AND EMBODIES CONFIDENTIAL
PROPRIETY INFORMATION. ALL RIGHTS IN THIS DOCUMENT AND THE
INFORMATION CONTAINED THEREIN ARE RESERVED. THIS DOCUMENT IS
PROVIDED IN CONFIDENCE FOR A SPECIFIC PURPOSE AND MAY NOT
BE USED, COPIED, OR DISCLOSED TO OTHERS FOR ANY OTHER PURPOSE
WITHOUT EXPRESS WRITTEN CONSENT OF KV. BY ACCEPTING THIS
DOCUMENT, THE RECIPIENT AGREES TO ABIDE BY THE FOREGOING
RESTRICTIONS AND TO RETURN THE DOCUMENT ON REQUEST WHEN THE
PERMITTED USE IS COMPLETE.
© 2012 KNAPE & VOGT MANUFACTURING COMPANY. ALL RIGHTS
RESERVED.
SHEET SIZE:
SCALE:
CHK'D BY:
1/14/2016
1:3
SURROUND ASSEMBLY
0335-SRND
RSS
C
SHEET 1 OF 1
Figure 1
Figure 2
ECN
REV
DATE
TOLERANCE UNLESS OTHERWISE SPECIFIED
3 PL DEC .005
2 PL DEC .010
ANGLES 1/2
MATERIAL:
FINISH:
N/A
2700 Oak Industrial Dr. NE
Grand Rapids, MI 49505
800-253-1561
www.kv.com
customer.service@kv.com
Figure 3
Figure 4
©2016 Knape & Vogt. KV and the KV logo are trademarks of Knape & Vogt.
310533/0616
DWN
DESC
PART
Auteur
Document
Catégorie
Uncategorized
Affichages
0
Taille du fichier
5 952 KB
Étiquettes
1/--Pages
signaler